分类目录归档:Atomizers

How about DIY atomizer coils? | KKEMC.COM

      How about DIY atomizer coils? I believe that many new users will ask questions about DIY atomizer coils, so let’s take a look at how to DIY atomizer coils.
      1. Prepare the RBA Atomizer and basic tools first. Of course, you can also use the voltage regulator to act as the console. The difference is that the 521 mini has a lower height and is more stable during operation.
      (It is not recommended to use a mechanical lever as the operating table. The mechanical lever does not have a protection circuit and there is a certain risk)
      2. Next, prepare the heating wire and the oblique cut. If you don’t have a diagonal cut, you can use a nail clipper instead, but you won’t be able to cut your nails after using it.

Tips: Many novice friends are more entangled, so many hot wire models and materials, how should we choose?
      The principle is: the filament is sucked by the mouth, the thick wire is used for the large smoke, the pressure regulating wire is used for the pressure regulation, and the temperature control wire is used for the temperature control.
      First you can choose according to your atomizer use:
      A, “mouth suction type atomizer” with filament 30Ga-26Ga (0.25-0.4mm), recommended to use 28Ga (0.32mm), almost suitable for any mouth-sucking type of RBA, single and double hair can be It has strong adaptability and stable taste. 26Ga (0.4mm) is not recommended, because it will be much lighter on a variety of mouth-sucking mouth-type atomizers;
      B, “large smoke atomizer” Whether it is to store oil or smoke, it is usually necessary to use thick wire. The vast majority of vapers use 22Ga (0.6mm) every day. If the novice is worried that the double-shot resistance is too low, you can start with 24Ga (0.5mm) first, and then use 22Ga after proficiency.
      There are so many material types in the heating wire, how do you choose?
Different materials, different modes are applicable. Nickel 200 can only be used for temperature control. It is forbidden to use voltage regulator and mechanical rod. 316 can be temperature-controlled or pressure-regulated. A1 can only regulate pressure, and the effect is stable. Nickel 80 can only be used. Used for voltage regulation, the resistance is lower than A1, and the heating speed is fast.
It must be noted that the nickel 200 cannot use the voltage regulation mode!
      3, cut the heating wire with a diagonal cut, pay attention to the right amount to avoid waste.
 
      Tips: Rhinoceros heating wire uses the most convenient “double strap” strapping method. Many novice friends sometimes cut off both straps, then they instantly “cups”… slowly reorganized with tears Let’s make a bunch of hot silk…
 
      In fact, the correct use of the “double strap” strapping method is to find one of the hair hot filaments, then move the strap, leave the appropriate length, and then cut the heating wire, adjust the position of the two straps to fix the heating wire head It’s fine, it doesn’t have to be cut, it’s very convenient.
      4. Cut the heating wire and then wind the coil. Wrap the heating wire around the wire rod and wrap it around the coil. When using a wire wrap, be careful to choose the right ring diameter.
 
      Tips: Ordinary wire-wound rods are suitable for use with filaments.
      If winding a thicker heating wire, it is recommended to use a winder. Because the winding of the wire rod is very laborious, it is easy to use with the pliers. It is not easy for the novice to master, and the coil will often be broken.
 
      When using the winder, you must first select the winding rod of the appropriate diameter. After installation, select the head of the corresponding specification to wrap it, which is easy to operate and saves time and effort.
But for filaments of 0.32 or less, it is not easy. Therefore, it is recommended that you use a winder for large smoke and thick wire, and use a wire rod for the taste-type filament.
 
      The effect of the winding of the winder and the winding rod is compared, and the coil made of the thick wire using the winder is more tidy and standardized.
      5, the winding of the coil, usually need to adjust and bend the two legs to fit the large pitch electrode column of the current atomizer.
 
      The tool used for adjustment can be a needle-nosed pliers, but in practice, the tweezers tend to be better.
First, insert the coil into the middle of the tweezer, push it up and hold it, then hold the tweezer in one hand to prevent the coil from falling, and the other hand bend the line to the sides.
 
      Then, according to the spacing of the threaded holes, the stitches are folded back, and the entire manufacturing process of the coil is completed.
 
      The adjusted coil shape is as shown above.
 
      “Dice” is the most practical “all-rounder” in the e-cigarette tool. In addition to the functions described above, it can also be used as a screwdriver to load and unload the 510 electrode screw on the bottom of the Atomizer, which can avoid the abrasion caused by the ordinary screwdriver.
      6. Insert the coil into the threaded hole and tighten the fixing screw. When fixed, the winding rod can be inserted into the coil to assist in installation, so as to avoid deformation of the coil due to the rotation of the screw.
 
      The position of the coil should refer to the air inlet, as far as possible above the air inlet, slightly to the electrode column, because the subsequent adjustment will slightly change the position of the coil, so that it is just above the air hole.
      7. In addition to making coils, the winding bar can also be used to assist the coil installation, avoid coil deformation, and adjust the position and height of the coil. It is also a versatile tool.
 
      In the production process, in addition to the fixed atomizer, the console and the main unit can detect the resistance of the coil and whether there is a short circuit or open circuit. Therefore, it is not recommended for the novice to use the mechanical rod to make the atomization core.
 
      In this example, the resistance measured by the console after the completion of the production was 0.24 Ω.
8, the next is the so-called “heating wire”, by heating the coil to heat and burn, so that the surface of the heating wire forms an oxide layer to insulate.
 
      It is also possible to observe whether the heating of the coil is uniform or synchronized by burning the wire.
To adjust the method, use a pair of tweezers to squeeze the ends of the coil slightly, or use a flat-blade screwdriver to gently scrape the outside of the coil.
Tips:
      Uniform heating of the coil means that it gradually turns red from the middle to the sides, and there is no particularly bright and particularly dark place.
      Coil heating synchronization means that two (multiple) heating wires work at the same time, and the heating speed and lighting time are consistent.
      The ceramic tweezers can be operated when the coil is energized, but the ordinary metal tweezers can only be heated and then released after the switch is turned off, otherwise the current will flow directly from the tweezers and the adjustment operation cannot be completed.
      When adjusting the coil, thoroughly burn it and then adjust it, so it is easier to heat evenly, but try to use low power to avoid excessive power and burn the coil.
      If the two coils are evenly heated after repeated adjustment, but the synchronism is poor, then it is necessary to check whether the coil fixing screws are tightened. In most cases, the coils can be heated synchronously after tightening the screws.
      9. After adjusting the coil, you can prepare the oil guiding cotton, and let the coil cool down to avoid the high temperature scorching after the cotton is penetrated.
 
      At present, there are many types of cotton used in e-cigarettes. Commonly used are organic cotton such as Gangwon-do and MUJI.
Another type is special cotton for electronic cigarettes, which is specially made according to the characteristics of high temperature of electronic cigarettes and high-speed oil guiding. Compared with ordinary cotton, it has no odor and high temperature resistance, and has less influence on the taste of e-liquid.
Most vapers now use “Bacon Cotton”, which has excellent performance, is inexpensive, and has a high price/performance ratio.
 
      The bacon cotton has a long strip shape, and the hand is used to tear the appropriate amount along the direction of the fiber, and then the fingers are repeatedly twisted and moved into a strip shape, and one end is forcefully twisted into a tapered shape to facilitate passage through the coil.
 
      Put the sliver into the coil and pull it back and forth several times to make it move. There is resistance. Pulling does not mean that the amount of cotton is too much, to remove some. If the resistance is small, it means that the amount of cotton is too small, it will cause oil and oil leakage. Add some cotton and then reinstall it.
      After adjusting the position of the cotton, cut off the excess cotton at both ends according to the structure and length of the oil path at the bottom of the atomizer.
 
      Use the tweezers to place the cotton according to the structure of the atomizer. Adjust the cotton on both sides of the coil to form a full ball. You can refer to the shape of the “cotton swab”.
      10. The final step is to thoroughly soak the cotton with smoky oil, then heat and blow the air to the atomizer coil to remove the odor of the cotton itself and the sweat remaining on the cotton.
 
      After heating, you can close the eyes with your nose and heat the air to check the smell of the smoke. If there is no smell, you can assemble the atomizer and add the e-liquid.
      This method must be careful to close your eyes, not too close to the atomizer coil, to prevent the smoke from collapsing into the eyes or scalding the nose. Although the method is very “two”, it is very effective.
      The reason why you recommend the use of cotton-specific cotton such as bacon cotton is because the chance of such odors is very low, and it can be used normally without burning cotton.
 
      At this point, the steps of the DIY atomizer are all over. Some commonly used tools are also introduced for everyone. Although it seems complicated, the DIY electronic cigarette is not so difficult. As long as it is fully prepared, it will be mastered through practice. After that, anyone can be skilled in making it.
      I hope this article will help you and start a happy Vape tour! Atomizer DIY Tools you can buy at KKEMC.COM

Atomizer Classification Introduction and How Atomizer Works? | KKEMC.COM

1. The atomizer classification:

A. Finished product sub ohm tank
B, RBA atomizer (Rebuild atomizer)
RBA can be divided into
1) RTA (Rebuild tank atomizer)
2) RDA (Rebuild drip atomizer)
3) RDTA (Rebuild drip tank atomizer)
The atomizer is the most important part of the electronic cigarette except the power supply equipment. The smoke is obtained by heating the heating wire in the atomizer to evaporate the E-liquid in the internal oil guiding cotton. The intake structure of the atomizer and the structure inside the atomizer greatly affect the taste during use.
2. the atomizer works:
The working principle of all atomizers is the same. Through the mains supply, the heating coil (or atomization core) in the atomizer is heated, the heating coil heats up, and the external (or internal) of the evaporation coil adsorbs e-liquid in the oil-guiding cotton. Then it takes away the atomized smoke through the airflow inhaled by the user. Any change in any one of these points will affect the taste of the e-liquid.
Atomizers are further divided into two categories based on the characteristics of their atomizing cores:
1) The finished atomizer, because it uses a disposable heater core matched with the atomizer, is called a finished atomizer (mostly an oil atomizer). Generally, DIY bases are not equipped (some products are equipped with DIY components). However, due to the structural problems of the finished heater cores, although resetting can be performed, the effect after the reset is generally difficult to reach the original effect and requires a longer time.
2) RBA atomizers, also known as reconfigurable atomizing core atomizers. It is not equipped with a finished atomizing core. Users are required to wind the heating coils by themselves and install heating coils and oil guiding cotton. According to its structure can be divided into three types: RTA, RDA, RDTA.
3) RTA is a reconfigurable oil atomizer, RDA is a reconstitutable oil drop atomizer, and RDTA is a drop oil atomizer with oil tank.
RBA structure features:
The structure of the finished atomizer is generally composed of a drip tip/mouthpiece, a top cover, an oil tank, a finished atomization core, and a base.
The RTA atomizer is generally composed of a drip tip(mouthpiece), a top cover, a atomizer chamber, an oil tank, an electrode and a base.
The RDA atomizer is generally composed of a drip tip(mouthpiece), a atomizer top cover, a atomization chamber, an electrode and a base.
The RDTA atomizer is generally composed of a drip tip(mouthpiece), a top cover of an atomization chamber, an atomization chamber, an electrode stage, and a bottom oil tank.
In general, the airway of the mouth-type atomizer is long and narrow, the internal space of the atomizer compartment and the air inlet are small, and there is an inverted cone-shaped gathering structure at the top of the atomizerr compartment, which can fully compress the smoke and improve the feeling of your mouth. Improve the fullness and clarity. The mouth-type atomizer generally has a small intake port, it can produce a strong suction resistance (the use of lung suction will be very difficult), so most of them use oral suction.
The air passages of large smoke atomizers are relatively thick (or have no air passages). Both the space inside the atomization chamber and the air inlet are relatively large, and the smoke and air can be sufficiently mixed to increase the volume of the smoke. The taste is mainly rich, because the use of lung suction is generally used, the time for the smoke to stay in the mouth is shorter, plumpness and sharpness will be slightly reduced.
Shopping suggestions:
1) Finished atomizers Due to the stability of the mouthfeel and the very simple operation mode, the finished atomizer is more suitable for those beginners or players who do not have time (or don’t want to do) to perform heating wire production.
2) The RTA atomizers have undergone such a long period of development and has begun to polarize. On the one hand, it is a mouth-sucking oil storage atomizer that favors the taste of E-liquid, and on the other hand, it is a large smoke lung suction storage atomizer that favors large smoke and also has a certain endurance. The simplest resolution method is to determine whether the mouthpiece suction type atomizer or a large smoke lung suction atomizer is based on the size of the air inlet of the atomizer.
3) The RDA drip atomizer also has the same polarize situation. Players can distinguish whether it is a large smoke drip atomizer or a mouthfeel atomizer according to the size of the atomization chamber and the air inlet. Generally speaking, it is a mouth-shaped atomizer. The smaller the atomization chamber and the smaller the air inlet will be the mouth-shaped drip atomizer.
4) The RDTA atomizer adds an oil reservoir to the RDA atomizer to improve the low oil storage of the RDA atomizer using cotton storage.
After many years of development, the atomizer has appeared in various styles due to the needs of the players. It is biased towards the finished atomizer used by novices, and it tends to taste the mouth-sucking atomizer of the e-liquid. A large smoke atomizer for experiencing the smog of the lungs. The endless stream of structural innovations is for players to get a better experience.
Links above could reach KKEMC.COM and you can shop e-cigarette accerssories online.